Thermoprobe TP9 User Manual Page 3
- Page / 51
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
11/2012, JK
REPLACING BATTERY
WARNING:
• Batteries must be changed in Non-hazardous area.
• Batteries must be of correct approved type.
• Batteries must be installed with correct polarity making sure the (+) end of the battery is aligned with (+) symbol embossed
in the battery case.
• New batteries must not be mixed with old batteries. Batteries must not be mixed with batteries of other manufacturers.
• Batteries must not be installed with polarity reversed where one cell could charge another cell.
a) Ensure the instrument is in a non-hazardous area.
b) Remove the 3 screws holding the front cover on the TP7C or the 2 screws holding the front cover on the TP9.
c) Remove battery retaining device, push one battery towards the spring contact and lift battery up from the holder, and then remove
the remaining battery.
d) Install each new battery making sure the (+) end of the battery is aligned with (+) symbol embossed in the battery case.
e) Replace the retaining device and reinstall the cover.
CERTIFIED Batteries for the TP9 and TP7C are as follows:
Manufacturer Type Part Number
Duracell AA (LR6) Alkaline MN1500
Panasonic AA (LR6) Alkaline LR6XWA
GP (Gold Peak) AA (LR6) Alkaline GP15A
MEASURING PROCEDURES
See www.thermoprobe.net
for video on proper use of this instrument. Contact your distributor or ThermoProbe Inc. for names of
training facilities. Refer to American Petroleum Institute measurement standard Chapter 7.2.
When the temperature has stabilized both Up and Down arrows will be displayed.
If you wish to log the temperature for averaging purposes, rapidly press the “On” button twice
. An acknowledgment of a saved
reading will occur with a display of “LoggEd”. If the display shows “-------“ then reading was not logged due to a non-stabilized
temperature. The real time temperature will then be displayed again indicating the next reading is ready to be taken.
If you have completed all the readings needed for your operation, the “f” Button may be used to “LiSt” all the readings logged and
“At” average of the logged temperatures. Document your readings and average temperature before powering off the device.
Logged readings and average are not saved when the instrument powers off. (Note: The instrument will automatically power off 20
minutes after the last button push.)
AUTHORIZED REPAIR
It is recommended that service beyond the scope of this manual be performed by ThermoProbe, Inc. or one of its authorized
distributors.
- 11/2012, JK 1
- CALIBRATION PROCEDURE 6
- Power Button 6
- Function Button 6
- Calibration Button 6
- REMPLACEMENT DES PILES 11
- PROCÉDURES DE MESURE 11
- RÉPARATEURS AGRÉÉS 11
- Codes d'erreur 13
- REMPLACEMENT DE LA SONDE 13
- Équipement nécessaire : 14
- 16
- PROCEDIMIENTOS DE MEDICIÓN 19
- REPARACIÓN AUTORIZADA 19
- CÓMO REEMPLAZAR LA BATERÍA 19
- Comprobación de la batería 21
- Códigos de error 21
- Terminal negativa 22
- ТЕРМОМЕТРОВ TP7C И TP9 26
- Задняя подсветка 30
- Проверка батарей 30
- Коды ошибок 30
- ЗАМЕНА ДАТЧИКА 30
- ПРОЦЕДУРА КАЛИБРОВКИ 31
- Отрицательная 31
- Кнопка включения питания 32
- Функциональная кнопка 32
- Кнопка калибровки 32
- Декларация соответствия 34
- PROCEDURE DI MISURAZIONE 37
- RIPARAZIONE AUTORIZZATA 37
- PROCEDURA DI CALIBRAZIONE 40
- DICHIARAZIONE DI CONFORMITA’ 42
- AUSTAUSCH DER BATTERIEN 45
- MESSVERFAHREN 45
- AUTORISIERTE REPARATUREN 45
- Fehlercodes 47
- ERSATZ DER SONDENEINHEIT 47
- KALIBRIERUNGSVERFAHREN 48
- Durch schwarze 48
- Lackierung 48
- Betriebstaste 49
- Funktionstaste 49
- Kalibrierungstaste 49
- KONFORMITÄTSERKLÄRUNG 51
Related products and manuals for Measuring instruments Thermoprobe TP9
(37 pages)Chief PSH2000 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Flachbildschirmhalterungen Chief PSH2000.
Wir stellen 1 PDF-Handbücher Chief PSH2000 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Installationshandbuch
Comments to this Manuals